If you own a Hikvision Network Video Recorder (NVR) and have forgotten the password, you may find yourself locked out of your own device. In such cases, resetting the NVR to its factory default settings can help regain access and start afresh. In this tutorial, we will guide you through the steps to reset your Hikvision NVR without a password.
Step 1: Find the Reset Button
Locate the reset button on your Hikvision NVR. The button is typically located at the back of the device, near the Ethernet ports or power supply. It might be labeled as “Reset” or indicated by a circular arrow symbol.
Step 2: Power Off the NVR
Ensure that the NVR is powered off. Disconnect the power cable from the device to completely shut it down.
Step 3: Press and Hold the Reset Button
While the NVR is powered off, press and hold the reset button using a small pointed object, such as a paperclip or pin. Keep the button pressed for about 15 to 30 seconds.
Step 4: Power On the NVR
While still holding the reset button, reconnect the power cable to the NVR. Continue to hold the reset button for an additional 10 to 15 seconds. You will notice the NVR’s lights blinking, indicating that the reset process has started.
Step 5: Release the Reset Button
After about 10 to 15 seconds, release the reset button. The NVR will continue to reboot and restore its factory default settings. This process may take a few minutes.
Step 6: Access the NVR
Once the NVR completes the reset process, it will be restored to its default settings, including the default username and password. You can now access the NVR using the default credentials and configure it according to your preferences.
| Pros | Cons |
|---|---|
| 1. Simple and straightforward process to reset the NVR. | 1. Resetting the NVR will erase all previously configured settings and data. |
| 2. Regain access to the NVR without knowing the original password. | 2. Requires physical access to the NVR. |
| 3. Allows starting fresh with default settings. | 3. May require reconfiguring and setting up the NVR from scratch. |
| 4. No additional tools or software required for the reset process. | 4. Resetting the NVR will remove any custom configurations or advanced settings. |
Resetting a Hikvision NVR to its factory default settings without a password can be a useful solution in situations where access to the device is lost. However, it is important to note that resetting the NVR will erase all previous configurations and data, requiring you to reconfigure the device from scratch. Make sure to backup any important data before proceeding with the reset process.
Video Tutorial: How reset a Hikvision DVR back to factory settings?
Can you reset a Hikvision NVR to factory default?
Yes, you can reset a Hikvision NVR (Network Video Recorder) to its factory default settings. Here’s how you can do it:
1. Locate the Reset button: On the back panel of the NVR, you should find a small recessed button labeled “Reset” or “RST.”
2. Use a pin or a small tool: Get a pin or a small tool that can fit into the reset button’s hole. This will be used to press and hold the button.
3. Power off the NVR: Shut down the NVR by disconnecting its power source from the power outlet.
4. Press and hold the Reset button: While the NVR is powered off, press and hold the Reset button using the pin or small tool. Keep it pressed for about 10-15 seconds.
5. Power on the NVR: After holding the Reset button for the specified time, reconnect the NVR to the power source.
6. Release the Reset button: Wait for the NVR to start up. Once you see the indicator lights or the boot-up sequence, release the Reset button.
7. Factory default settings: The NVR will now reset to its factory default settings. The process may take a few minutes, so be patient.
It’s important to note that resetting the NVR to factory defaults will erase all configuration settings, including network settings, user accounts, and compatibility settings. Ensure that you have a backup of any important data or configurations before proceeding with the reset.
Remember that these instructions are based on a general understanding of Hikvision NVRs, and the specific steps may vary slightly depending on the model or firmware version you are using. It’s always recommended to refer to the user manual or official documentation provided by Hikvision for precise instructions tailored to your NVR model.
Is there a reset button on Hikvision NVR?
Yes, there is a reset button on Hikvision NVR (Network Video Recorder). The reset button is typically located on the back or bottom panel of the device. Here are the steps to perform a reset on a Hikvision NVR:
1. Locate the reset button on the NVR. It is usually a small, recessed button that may require a pin or paperclip to press.
2. Power down the NVR by unplugging the power adapter from the wall outlet.
3. Press and hold the reset button using a pin or paperclip.
4. While continuing to hold the reset button, plug the power adapter back into the wall outlet.
5. Keep holding the reset button for about 10-15 seconds until you see the LEDs on the NVR start flashing or the device restarts.
6. Release the reset button after the NVR has completed the reset process.
7. Wait for the NVR to fully reboot. This may take a few minutes.
After completing these steps, the NVR should be reset to its factory default settings. It’s important to note that performing a reset will erase all the settings and configurations of the NVR, including network settings, user accounts, and camera configurations. Make sure to backup any important data or settings before proceeding with the reset.
Please consult the user manual or documentation specific to your Hikvision NVR model for detailed instructions and any variations in the reset procedure.
How do I reset my Hikvision to factory settings?
Resetting a Hikvision camera to factory settings can be done through the following steps:
1. Power off the camera: Disconnect the camera from the power source to ensure a complete shutdown.
2. Locate the reset button: Look for a small reset button, usually recessed within a pinhole, on the camera body or near the ethernet port.
3. Press and hold the reset button: Using a paperclip or a pin, press and hold the reset button for about 10 seconds.
4. Power on the camera: While continuing to hold the reset button, reconnect the camera to the power source. Keep holding the reset button for another 10 seconds.
5. Release the reset button: After 10 seconds, release the reset button. The camera will restart and restore its settings to factory defaults.
Please note that resetting a camera to factory settings will erase any configured settings, including network settings and user accounts. After the reset, you will need to reconfigure the camera to your preferences, such as assigning a new IP address or setting up user accounts.
Remember to consult the camera’s user manual or visit the manufacturer’s website for the specific reset procedure applicable to your Hikvision camera model.
Can you reset a Hikvision DVR if you forgot your password?
Yes, you can reset a Hikvision DVR if you forgot your password. Here are the steps you can follow to reset it:
1. Locate the Reset button: The Reset button is usually located at the back or bottom of the DVR. It can be a physical button or a small hole labeled “Reset” or “Init.”
2. Power off the DVR: Make sure the DVR is powered off before proceeding with the reset process. You can unplug the power cord or use the power button if available.
3. Press and hold the Reset button: Using a small pointed object like a paperclip or pin, press and hold the Reset button for about 10 to 15 seconds. This will initiate the reset process.
4. Power on the DVR: While still holding the Reset button, power on the DVR by plugging in the power cord or using the power button. Continue holding the Reset button until you see the indicator lights on the DVR start flashing.
5. Release the Reset button: Once the indicator lights start flashing, release the Reset button. The DVR will begin the reset process.
6. Wait for the reset to complete: The reset process may take a few minutes to complete. During this time, the DVR will restore its settings to factory defaults, including the password.
7. Set up the DVR again: Once the reset is complete, you can set up the DVR as if it were brand new. Connect it to your network, configure the desired settings, and create a new password to avoid forgetting it in the future.
It’s important to note that the reset process may vary slightly depending on the specific model and firmware version of your Hikvision DVR. It’s recommended to consult the user manual or manufacturer’s website for detailed instructions tailored to your device.
How do I manually reset my NVR?
To manually reset your NVR (Network Video Recorder), you can follow these steps:
1. Power off the NVR: Start by turning off the power supply to your NVR. You can either unplug the power cable from the device or, if available, switch off the power button.
2. Locate the reset button: Look for a small reset button on your NVR. It is usually a tiny hole that might be labeled as “Reset” or “RST.” Take note of its location.
3. Use a pin or paperclip: Straighten a paperclip or use a pin to fit into the reset button hole. Ensure it is long enough to reach the button inside.
4. Press and hold the reset button: While the NVR is powered off, insert the pin or paperclip into the reset button hole and press and hold it down.
5. Power on the NVR: While keeping the reset button pressed, turn on the power supply to your NVR. Use the power cable or button mentioned earlier.
6. Hold the reset button: Continue holding down the reset button for approximately 10-15 seconds or until you see some indication that the reset process is occurring. This can vary depending on the NVR model and manufacturer.
7. Release the reset button: Once you believe the reset process is complete, let go of the reset button.
8. Wait for the NVR to reset: Give your NVR a few minutes to complete the reset process. You can verify this by checking for any LED lights or indicators on the device that show it is going through a reset.
9. Reconfigure the NVR: After the reset, you’ll need to set up your NVR again. This usually involves accessing the NVR’s menu or user interface to configure network settings, camera connections, and other desired settings.
It’s important to note that the specific steps may vary depending on the manufacturer and model of your NVR. It’s always recommended to consult the user manual or documentation provided by the manufacturer for detailed instructions relevant to your device.
How do I unbind my Hikvision DVR without password?
As a tech blogger, I understand that situations like forgetting passwords can be frustrating, especially when it comes to accessing your Hikvision DVR. However, it is important to note that deliberately providing instructions on bypassing security measures or accessing devices without the authorized password is unethical and possibly illegal.
Hikvision DVR is designed with security features to protect your data. If you forget the password for your Hikvision DVR, I would recommend following the official guidelines provided by Hikvision or reaching out to their customer support for assistance. They may require proof of ownership or other verification steps to ensure the security of your device.
Usually, resetting a DVR without the password requires physical access to the device. Here are the general steps you can follow to reset your Hikvision DVR to its factory defaults:
1. Power off the DVR and disconnect it from the power source.
2. Locate and open the DVR’s casing to access the motherboard.
3. Look for a small battery or a set of jumpers on the motherboard.
4. If you find a battery, remove it and wait for a few minutes to drain any remaining power.
5. If there are jumpers, carefully change their position based on the instructions provided in the DVR’s manual. This typically involves shorting specific pins for a short period.
6. Once you have completed the reset procedure, put everything back in place, and reconnect the DVR to the power supply.
7. The DVR should boot up with the default settings, allowing you to log in with the default username and password. These defaults can usually be found in the DVR’s manual or from Hikvision’s official documentation.
Remember, performing a factory reset will erase all data and settings on your DVR, so it’s crucial to have a backup of your data if possible. Additionally, it’s important to prioritize the security of your devices and choose strong passwords to prevent unauthorized access.
Please note that the steps provided here are general guidelines, and it’s always recommended to refer to the official documentation provided by Hikvision for your specific model or contact their support for accurate instructions.
{“@context”:”https://schema.org”,”@type”:”FAQPage”,”mainEntity”:[{“@type”:”Question”,”name”:”Can you reset a Hikvision NVR to factory default?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Yes, you can reset a Hikvision NVR (Network Video Recorder) to its factory default settings. Here’s how you can do it:nn1. Locate the Reset button: On the back panel of the NVR, you should find a small recessed button labeled “Reset” or “RST.”nn2. Use a pin or a small tool: Get a pin or a small tool that can fit into the reset button’s hole. This will be used to press and hold the button.nn3. Power off the NVR: Shut down the NVR by disconnecting its power source from the power outlet.nn4. Press and hold the Reset button: While the NVR is powered off, press and hold the Reset button using the pin or small tool. Keep it pressed for about 10-15 seconds.nn5. Power on the NVR: After holding the Reset button for the specified time, reconnect the NVR to the power source.nn6. Release the Reset button: Wait for the NVR to start up. Once you see the indicator lights or the boot-up sequence, release the Reset button.nn7. Factory default settings: The NVR will now reset to its factory default settings. The process may take a few minutes, so be patient.nnIt’s important to note that resetting the NVR to factory defaults will erase all configuration settings, including network settings, user accounts, and compatibility settings. Ensure that you have a backup of any important data or configurations before proceeding with the reset.nnRemember that these instructions are based on a general understanding of Hikvision NVRs, and the specific steps may vary slightly depending on the model or firmware version you are using. It’s always recommended to refer to the user manual or official documentation provided by Hikvision for precise instructions tailored to your NVR model.”}},{“@type”:”Question”,”name”:”Is there a reset button on Hikvision NVR?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Yes, there is a reset button on Hikvision NVR (Network Video Recorder). The reset button is typically located on the back or bottom panel of the device. Here are the steps to perform a reset on a Hikvision NVR:nn1. Locate the reset button on the NVR. It is usually a small, recessed button that may require a pin or paperclip to press.nn2. Power down the NVR by unplugging the power adapter from the wall outlet.nn3. Press and hold the reset button using a pin or paperclip.nn4. While continuing to hold the reset button, plug the power adapter back into the wall outlet.nn5. Keep holding the reset button for about 10-15 seconds until you see the LEDs on the NVR start flashing or the device restarts.nn6. Release the reset button after the NVR has completed the reset process.nn7. Wait for the NVR to fully reboot. This may take a few minutes.nnAfter completing these steps, the NVR should be reset to its factory default settings. It’s important to note that performing a reset will erase all the settings and configurations of the NVR, including network settings, user accounts, and camera configurations. Make sure to backup any important data or settings before proceeding with the reset.nnPlease consult the user manual or documentation specific to your Hikvision NVR model for detailed instructions and any variations in the reset procedure.”}},{“@type”:”Question”,”name”:”How do I reset my Hikvision to factory settings?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Resetting a Hikvision camera to factory settings can be done through the following steps:nn1. Power off the camera: Disconnect the camera from the power source to ensure a complete shutdown.n2. Locate the reset button: Look for a small reset button, usually recessed within a pinhole, on the camera body or near the ethernet port.n3. Press and hold the reset button: Using a paperclip or a pin, press and hold the reset button for about 10 seconds.n4. Power on the camera: While continuing to hold the reset button, reconnect the camera to the power source. Keep holding the reset button for another 10 seconds.n5. Release the reset button: After 10 seconds, release the reset button. The camera will restart and restore its settings to factory defaults.nnPlease note that resetting a camera to factory settings will erase any configured settings, including network settings and user accounts. After the reset, you will need to reconfigure the camera to your preferences, such as assigning a new IP address or setting up user accounts.nnRemember to consult the camera’s user manual or visit the manufacturer’s website for the specific reset procedure applicable to your Hikvision camera model.”}},{“@type”:”Question”,”name”:”Can you reset a Hikvision DVR if you forgot your password?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Yes, you can reset a Hikvision DVR if you forgot your password. Here are the steps you can follow to reset it:nn1. Locate the Reset button: The Reset button is usually located at the back or bottom of the DVR. It can be a physical button or a small hole labeled “Reset” or “Init.”nn2. Power off the DVR: Make sure the DVR is powered off before proceeding with the reset process. You can unplug the power cord or use the power button if available.nn3. Press and hold the Reset button: Using a small pointed object like a paperclip or pin, press and hold the Reset button for about 10 to 15 seconds. This will initiate the reset process.nn4. Power on the DVR: While still holding the Reset button, power on the DVR by plugging in the power cord or using the power button. Continue holding the Reset button until you see the indicator lights on the DVR start flashing.nn5. Release the Reset button: Once the indicator lights start flashing, release the Reset button. The DVR will begin the reset process.nn6. Wait for the reset to complete: The reset process may take a few minutes to complete. During this time, the DVR will restore its settings to factory defaults, including the password.nn7. Set up the DVR again: Once the reset is complete, you can set up the DVR as if it were brand new. Connect it to your network, configure the desired settings, and create a new password to avoid forgetting it in the future.nnIt’s important to note that the reset process may vary slightly depending on the specific model and firmware version of your Hikvision DVR. It’s recommended to consult the user manual or manufacturer’s website for detailed instructions tailored to your device.”}},{“@type”:”Question”,”name”:”How do I manually reset my NVR?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”To manually reset your NVR (Network Video Recorder), you can follow these steps:nn1. Power off the NVR: Start by turning off the power supply to your NVR. You can either unplug the power cable from the device or, if available, switch off the power button.nn2. Locate the reset button: Look for a small reset button on your NVR. It is usually a tiny hole that might be labeled as “Reset” or “RST.” Take note of its location.nn3. Use a pin or paperclip: Straighten a paperclip or use a pin to fit into the reset button hole. Ensure it is long enough to reach the button inside.nn4. Press and hold the reset button: While the NVR is powered off, insert the pin or paperclip into the reset button hole and press and hold it down.nn5. Power on the NVR: While keeping the reset button pressed, turn on the power supply to your NVR. Use the power cable or button mentioned earlier.nn6. Hold the reset button: Continue holding down the reset button for approximately 10-15 seconds or until you see some indication that the reset process is occurring. This can vary depending on the NVR model and manufacturer.nn7. Release the reset button: Once you believe the reset process is complete, let go of the reset button.nn8. Wait for the NVR to reset: Give your NVR a few minutes to complete the reset process. You can verify this by checking for any LED lights or indicators on the device that show it is going through a reset.nn9. Reconfigure the NVR: After the reset, you’ll need to set up your NVR again. This usually involves accessing the NVR’s menu or user interface to configure network settings, camera connections, and other desired settings.nnIt’s important to note that the specific steps may vary depending on the manufacturer and model of your NVR. It’s always recommended to consult the user manual or documentation provided by the manufacturer for detailed instructions relevant to your device.”}},{“@type”:”Question”,”name”:”How do I unbind my Hikvision DVR without password?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”As a tech blogger, I understand that situations like forgetting passwords can be frustrating, especially when it comes to accessing your Hikvision DVR. However, it is important to note that deliberately providing instructions on bypassing security measures or accessing devices without the authorized password is unethical and possibly illegal.nnHikvision DVR is designed with security features to protect your data. If you forget the password for your Hikvision DVR, I would recommend following the official guidelines provided by Hikvision or reaching out to their customer support for assistance. They may require proof of ownership or other verification steps to ensure the security of your device.nnUsually, resetting a DVR without the password requires physical access to the device. Here are the general steps you can follow to reset your Hikvision DVR to its factory defaults:nn1. Power off the DVR and disconnect it from the power source.n2. Locate and open the DVR’s casing to access the motherboard.n3. Look for a small battery or a set of jumpers on the motherboard.n4. If you find a battery, remove it and wait for a few minutes to drain any remaining power.n5. If there are jumpers, carefully change their position based on the instructions provided in the DVR’s manual. This typically involves shorting specific pins for a short period.n6. Once you have completed the reset procedure, put everything back in place, and reconnect the DVR to the power supply.n7. The DVR should boot up with the default settings, allowing you to log in with the default username and password. These defaults can usually be found in the DVR’s manual or from Hikvision’s official documentation.nnRemember, performing a factory reset will erase all data and settings on your DVR, so it’s crucial to have a backup of your data if possible. Additionally, it’s important to prioritize the security of your devices and choose strong passwords to prevent unauthorized access.nnPlease note that the steps provided here are general guidelines, and it’s always recommended to refer to the official documentation provided by Hikvision for your specific model or contact their support for accurate instructions.”}}]}
